How To Change Battery Tpms? [Updated On- 2023] (2023)

Last Updated on September 22, 2022 by Ellis Gibson (B.Sc. in Mechanical Engineering)

If you’re like most people, you probably don’t know how to change your battery TPMS. That’s because the average person doesn’t know what TPMS is. TPMS stands for Tire Pressure Monitoring System. It’s a system that monitors the pressure in your tires and alerts you when the pressure gets too low.

So, how to change battery tpms?

There are a few things you need to do in order to change your car’s battery TPMS:

1. Find the right size battery for your car. Make sure to get the correct size, as this will ensure that the TPMS will work properly.

2. Once you have the new battery, disconnect the old one from the car.

3. Connect the new battery to the car, being careful to connect the positive and negative terminals correctly.

4. Start the car and let the new battery charge for a few minutes.

5. Once the car is running, the new battery should be fully charged and the TPMS should be working properly.

Let’s dig into it and see if we can get to the bottom of it.

# Table of Contents

Step By Step Process On: How To Change Battery Tpms?

Here I will explain you step by step process of how to change battery tpms? let’s see how to change battery tpms.


  1. TPMS diagnostic device
  2. Screwdriver
  3. Soldering iron
  4. Circuit board
  5. Battery
  6. Silicon sealant


First, use a TPMS diagnostic device to check if the sensor is truly bad. If it is, then proceed to the next step.


(Video) How To Replace TPMS Battery ( tire pressure sensor battery replacement )

Using a screwdriver, open up the sensor by prying open the two notches/tabs.


Carefully remove the circuit board and battery from the sensor housing.


Thoroughly clean the circuit board and battery contacts of any silicone residue.


Using a soldering iron, remove the two old battery contacts from the circuit board.


Clean the solder pads on the circuit board.


Place the new battery in the housing, making sure the plus and minus terminals are not touching.


Solder the new battery contacts to the circuit board.


Test the sensor to make sure it is working properly.


using a thinned out silicon sealant, reseal the sensor housing.

If you wanted to watch a youtube video that shows you how to change battery tpms? I have included a video below:

(Video) How to activate brand new TPMS sensor.

Can You Change Battery In Tpms Sensor?

“Can you change the battery in a TPMS sensor?”

This is a common question we get here at the Tire Pressure Monitoring System (TPMS) Help Desk. The answer is unfortunately, no. Most TPMS sensors run on batteries that are built into the sensor and these batteries are not replaceable. The life expectancy of the lithium ion batteries in a TPMS sensor is anywhere from 5-10 years.

So if your TPMS sensor is giving you a low battery warning, or it just stops working altogether, the only thing you can do is replace the entire sensor. This can be a bit of a pain, as you’ll need to re-learn the sensor to your vehicle’s TPMS system, but it’s really the only option.

We know it’s not the answer you were hoping for, but at least now you know what to do if your TPMS sensor starts acting up.

Moreover, When a car has a TPMS sensor, it is important to know that the batteries in the sensor will need to be replaced at some point. The life expectancy of the batteries in a TPMS sensor is 5-10 years.

How Do I Replace An External Tpms Battery?

If your car has an external Tire Pressure Monitoring System (TPMS) sensor, you may need to replace the battery at some point. Here’s a quick guide on how to do it:

1. Locate the sensor on your tire. It will be a small, round device that is mounted to the wheel.

2. Unscrew the sensor from the wheel.

3. Remove the old battery from the sensor.

4. Install a new CR2032 battery in the sensor.

5. Screw the sensor back onto the wheel.

And that’s it! You’ve now successfully replaced the battery in your external TPMS sensor.

Can You Reset Tpms After Changing Battery?

If you’ve recently changed your car battery, you may need to reset the TPMS (tire pressure monitoring system). Here’s how:

With the vehicle off, turn the key to the “on” position. Locate the TPMS reset button – it’s usually located beneath the steering wheel. Hold the TPMS reset button until the Toyota tire pressure sensor blinks three times. Release the button and start the car. Wait 20 minutes for the sensor to refresh.

And that’s it! After following these steps, your TPMS should be reset and working properly again.

Along with, If you want to reset your tire pressure sensor, you can do it by following these steps. First, turn the key to the “on” position without starting the car. Then, find the TPMS reset button and hold it until the sensor blinks three times. After that, you can start the car and wait for the sensor to refresh, which should take about 20 minutes.

Can I Change A Tpms Myself?

If you have a snap-in TPMS sensor, then you can easily change it yourself without any special tools. All you need is a conventional valve stem. However, if your TPMS sensor has a hex nut stem, then you will need to carefully tighten it to the specific value using an accurate inch-pound torque wrench or TPMS valve stem tool.

(Video) How To Replace TPMS (Tire Pressure Monitoring System) Sensors Without A Tire Machine.

Moreover, Snap-in TPMS sensors that have a rubber stem are as easy to replace as any conventional valve stem. No special tools are needed. But hex nut stems do have to be carefully tightened to specific value with an accurate inch-pound torque wrench or TPMS valve stem tool.

What Happens When Tpms Battery Dies?

If the TPMS battery dies, the system will need to be reset.

How Do I Replace The Battery In My Toyota’S Tpms System?

If your Toyota’s Tire Pressure Monitoring System (TPMS) light is on, it means that one or more of your tires is low on air. You’ll need to add air to the tire (or tires) in question to turn off the light.

If the TPMS light is flashing, it means that the system is not functioning properly and you should take your car to a Toyota dealer or certified repair shop to have it checked out.

To check your Toyota’s tire pressure, you’ll need a tire pressure gauge. You can find one at most auto parts stores.

To add air to your tires, you’ll need an air compressor. You can find one at most gas stations.

Once you have a tire pressure gauge and an air compressor, follow these steps:

1. Park your Toyota in a safe place. Make sure the engine is turned off and the parking brake is engaged.

2. Locate the tire that is low on air. It will likely be the one closest to the TPMS light on your dash.

3. Remove the cap from the tire valve.

4. Attach the tire pressure gauge to the tire valve and take a reading.

5. If the tire pressure is low, add air to the tire until it reaches the recommended pressure.

6. Remove the air compressor hose from the tire valve.

7. Replace the cap on the tire valve.

8. Repeat steps 2-7 for each tire that is low on air.

9. Once all tires are inflated to the proper pressure, the TPMS light should turn off.

How To Test Tpms Sensor Battery?

To test the TPMS sensor battery, you will need a multimeter. Begin by setting the multimeter to the 20 V DC setting. Next, locate the TPMS sensor on the vehicle. The sensor is typically located on the inside of the wheel well. Once you have located the sensor, remove the cap from the valve stem. With the multimeter probe, touch the positive lead to the TPMS sensor’s battery terminal. The negative lead should touch the metal valve stem. If the multimeter reading is above 1.5 volts, the battery is good. If the reading is below 1.5 volts, the battery needs to be replaced.

How To Replace Tpms Sensor?

Replacing a TPMS sensor is not difficult, but it does require a few steps. First, you’ll need to locate the sensor. Second, you’ll need to remove the old sensor. Third, you’ll need to install the new sensor. Finally, you’ll need to test the new sensor to make sure it’s working properly.

(Video) How To: Replace TPMS Battery

What Are The Consequences Of Not Changing The Battery In A Tpms Sensor?

If a TPMS sensor’s battery is not changed, the sensor will eventually die and will need to be replaced.

What Are The Symptoms Of A Tpms Sensor With A Dying Battery?

Typically, a TPMS sensor with a dying battery will exhibit one or more of the following symptoms: the sensor may stop transmitting data altogether, the sensor may transmit data intermittently, or the sensor may only transmit data when the vehicle is turned on.

How Often Should You Change The Battery In A Tpms Sensor?

You should change the battery in a TPMS sensor every 5-7 years.

Is It Possible To Change The Battery In A Tpms Sensor Without Resetting It?

Yes, it is possible to change the battery in a TPMS sensor without resetting it.

What Are The Benefits Of Changing The Battery In A Tpms Sensor?

One benefit of changing the battery in a TPMS sensor is that it can help prolong the sensor’s life. Additionally, changing the battery can also help ensure that the sensor is accurate.

Final Word

You’ve done it! You’ve changed your battery tpms! Here’s how:

1. Open the back of your car.

2. Unscrew the old battery tpms.

3. Screw in the new battery tpms.

4. Close the back of your car.

And that’s it! You’ve now changed your battery tpms and are ready to hit the road!


How Often Does The Battery Need To Be Replaced In The Ford Tpms Sensor?

According to the Ford website, the battery in the TPMS sensor should be replaced every seven years.

How Long Do Tpms Batteries Last?

Transitional words can vary depending on which question is being asked, but some common transitional words used to ask about the duration of something are “for how long,” “how long ago,” and “how long will.” In this case, a good transitional word to use would be “how long do.”

How long do TPMS batteries last? The average TPMS battery will last between 3 and 5 years. However, some batteries may need to be replaced sooner if the vehicle is driven in extreme conditions or if the battery is frequently drained.

What Is The Tpms Battery Replacement Cost?

The cost to replace the battery in a TPMS system varies depending on the make and model of the vehicle. However, the average cost is between $50 and $100.

What Is The Average Cost To Replace A Gm Tpms Battery?

The average cost to replace the battery in a GM vehicle’s Tire Pressure Monitoring System (TPMS) is $106. However, the cost can range from $86 to $125.

Related Post:

  • How to change battery trijicon rmr?
  • How to change battery ux301la?
  • How to change battery vf commodore key?
  • How to change battery vf commodore?
  • How to change battery vivint door lock?


1. Updated: BMW Motorcycle TPMS Battery Replacement
2. WHY Your Tire Light is ON & EASY FIX
(Silver Cymbal)
3. TST 770 New upgraded Monitor for your TPMS /Features and set up
(Jonesin 2 Go)
(Rain City Wrench)
5. Hyundai TPMS Metal Valve Stem Replacement & Reset
(GREEN Auto Services)
6. ✅ Top 5 Best OBD2 Scanner With TPMS Reset In 2023
(10 Star)
Top Articles
Latest Posts
Article information

Author: Errol Quitzon

Last Updated: 11/15/2022

Views: 5423

Rating: 4.9 / 5 (59 voted)

Reviews: 82% of readers found this page helpful

Author information

Name: Errol Quitzon

Birthday: 1993-04-02

Address: 70604 Haley Lane, Port Weldonside, TN 99233-0942

Phone: +9665282866296

Job: Product Retail Agent

Hobby: Computer programming, Horseback riding, Hooping, Dance, Ice skating, Backpacking, Rafting

Introduction: My name is Errol Quitzon, I am a fair, cute, fancy, clean, attractive, sparkling, kind person who loves writing and wants to share my knowledge and understanding with you.